CORE COMPONENTS
FOR MAX UPTIME

Jib Boom Rotary Actuator Conversion Kits

In Schramm’s continued effort to ensure our customers have access to top quality and reliable products, we are alerting you that the Helac Rotary Actuators, used to pivot the Jib Boom, are no longer being offered. This is due to lead time uncertainty and general difficulty in obtaining the part.

In its place, Schramm has designed a new pivoting system which has been implemented on new rig builds with great success. We are now offering it as a field kit for those rigs that continue to operate with the Helac Rotary Actuator. Our kits include all of the interface components and hardware.

Rigs affected are T300M rigs and most of the T450 Series rigs with approximate build years between 1992 through 2010. By providing the rig serial number we can determine which system was used when originally built and offer the correct conversion kits.

Two Speed Top Drive Motor Upgrade Kits

In Schramm’s continued effort to ensure our customers have access to top quality and reliable products, we are proactively alerting you that vendor Char Lynn has developed a new series of top head drive motors specifically for Schramm. The current 10K two speed motors will no longer be supported and while they will still be offered for a limited time, lead times may be longer than usual.

As Charlynn top head drive motors are integral and unique to Schramm Telemast rig models T90XD, T130XD, T200XD, TXD, T250XD, we are offering four kit options to provide you with a cost and time effective solution.

Schramm’s kit options replace most common instalments with the new HP30 series motors from Char Lynn. This will cover all two or four motor configurations and with multiple cubic inch displacements to achieve the desired speeds and torque.

These new motors are unique to the Schramm product and have been developed to be plug and play. They do not require any modifications to the hydraulic settings or hydraulic plumbing. Other displacements are available upon special request. In all cases the HP30’s are not backwards compatible with the 10k Series motors and must be replaced in pairs, two or four depending on your configuration.

Complete Mast Load Path Overhaul Kits

After years of hard work is the load path system on your drilling rig ready for an overhaul? Schramm Aftermarket is here to provide you with all the components you require to successfully replace all the worn out components of the load path system in one competitively priced bundle package. Components included in the mast load path overhaul are specific to each rig model however you can expect to have the package include the following components dependent on rig requirements.

Components
Pull Back and Pull Down Chains
Upper Sprocket, and Shaft
Double Travel Sprocket, and Shaft
Pull Down Travel Sprocket, and Shaft
Pull Down Sprocket and Shaft
Thrust Washers
Sheave Pins
Sheave Bushings
Traveling Blocks
Timing Shafts
New Feed Cylinder(s) (if required)

Please inquire with Schramm Aftermarket on our current pricing, and offerings to meet your rig mast overhaul needs. These kits will be put together to meet your specific rig needs. They are bundled to save you time and money over sourcing each individual component.

Complete Table Overhaul Kits

After years of hard work is the table on your rig worn out and ready for an overhaul? Schramm Aftermarket is here to provide you with all the components you require to successfully replace all the worn out components of the mast table in one competitively priced bundle package. Components included in the mast table overhaul are specific to each rig model however you can expect to have the package tailored to meet your specific rigs table, and include the following components dependent on rig requirements.

Components
Clam Shell Jaw Halves
Swing Table
Master Slip
Slip Guides
Casing Slips
Pipe Slips
Bushings
Adaptor Slips
Holding Fork (if Required)
Holding Fork Cylinder (if Required)
Rear Table Cylinder (if Required)

Please inquire with Schramm Aftermarket on our current pricing, and offerings to meet your rig table needs. These kits will be put together to meet your specific rig requirements. They are bundled to save you time and money over sourcing each individual component.

TXD 5000 PSI Conversion Kits

Update your TXD to the 5000 PSI Plumbing system. The 5000 PSI system will replace your lower pressure rated air mud lines, mud hoses, and top drive swivel s with 5000 PSI certified plumbing.

Field Kit #’s 3039-0600, 3039-0601, and 3039-0658

250, 500 and 1000 Hour Maintenance Kits

Drill rig uptime is important to Schramm, and the best way to maintain it is to perform the routine recommended periodic maintenance for your rig. Schramm is offering 250, 500 and 1000 hour recommended periodic maintenance kits to help keep your drill rig in peak operating condition. Contents of the kits will include the recommended service components and filters for your rigs 250, 500 and 1000 hour maintenance programs.

Contents of the kit vary by the rig model, however will generally include the following based on your rig options. If ordering a 1000 hour kit it will include all components needed to perform the 250, and 500 hour recommended periodic maintenance changes.

Engine
Oil Filter
Fuel Filters
Primary / Secondary Air Filters
Coolant Filter
Belt

Hydraulic
Filters
Magnetic Separators
Breather
Coalescing Filter

Compressor
Oil Filter
Separator Filter Kit
Coalescing Filter Element
In Line Filter

Pump Gearbox
Breather

Rotation Gearbox
Breather

These kits will be put together to meet your specific rig needs. They are bundled to save you time and money over sourcing each individual component.